diff options
| -rw-r--r-- | conf.d/network.Linux | 30 | ||||
| -rw-r--r-- | conf.d/network.in | 7 |
2 files changed, 19 insertions, 18 deletions
diff --git a/conf.d/network.Linux b/conf.d/network.Linux index 395c1cc6..3c230fe9 100644 --- a/conf.d/network.Linux +++ b/conf.d/network.Linux @@ -1,27 +1,27 @@ # ifconfig under Linux is not that powerful and doesn't easily handle # multiple addresses # On the other hand, ip (iproute2) is quite powerful and is also supported -# ip_eth0="192.168.0.10/24; 192.168.10.10/24" +#ip_eth0="192.168.0.10/24; 192.168.10.10/24" # Create a bonded interface -# interfaces="bond0" -# ifup_bond0="modprobe bonding; ifconfig \$int up; ifenslave \$int bge0" -# ifconfig_bond0="192.168.0.10 netmask 255.255.255.0" -# ifdown_bond0="rmmod bonding" +#interfaces="bond0" +#ifup_bond0="modprobe bonding; ifconfig \$int up; ifenslave \$int bge0" +#ifconfig_bond0="192.168.0.10 netmask 255.255.255.0" +#ifdown_bond0="rmmod bonding" # Create a bridged interface - let dhcpcd configure the address -# interfaces="br0" -# ifup_br0="brctl addbr \$int; brctl add \$int eth1; brtctl add \$int eth2" -# ifdown_br0="ifconfig \$int down; btctl delbr \$int" +#interfaces="br0" +#ifup_br0="brctl addbr \$int; brctl add \$int eth1; brtctl add \$int eth2" +#ifdown_br0="ifconfig \$int down; btctl delbr \$int" # Create VLAN -# interfaces="eth0_2 eth0_3 eth0_4" -# ifup_eth0="vconfig add \$int 2; vconfig add \$int 3; vconfig add \$int 4" -# ifconfig_eth0_2="192.168.2.10 netmask 255.255.255.0" -# ifconfig_eth0_3="192.168.3.10 netmask 255.255.255.0" -# ifconfig_eth0_4="192.168.4.10 netmask 255.255.255.0" -# ifdown_eth0="vconfig rem \$int.2; vconfig rem \$int.3; vconfig rem \$int.4" +#interfaces="eth0_2 eth0_3 eth0_4" +#ifup_eth0="vconfig add \$int 2; vconfig add \$int 3; vconfig add \$int 4" +#ifconfig_eth0_2="192.168.2.10 netmask 255.255.255.0" +#ifconfig_eth0_3="192.168.3.10 netmask 255.255.255.0" +#ifconfig_eth0_4="192.168.4.10 netmask 255.255.255.0" +#ifdown_eth0="vconfig rem \$int.2; vconfig rem \$int.3; vconfig rem \$int.4" # Normally you would use wpa_supplicant to configure wireless, but you can # use iwconfig also -# ifup_wlan0="iwconfig \$int key s:secretkey enc open essid foobar" +#ifup_wlan0="iwconfig \$int key s:secretkey enc open essid foobar" diff --git a/conf.d/network.in b/conf.d/network.in index a0162057..2719fa87 100644 --- a/conf.d/network.in +++ b/conf.d/network.in @@ -2,15 +2,16 @@ # Seperate commands with ; # Prefix with ! to run a shell script. # Use \$int to represent the interface -# ifconfig_eth0="192.168.0.10 netmask 255.255.255.0" +#ifconfig_eth0="192.168.0.10 netmask 255.255.255.0" # You also have ifup_eth0 and ifdown_eth0 to run other commands when # eth0 is started and stopped. # You can assign a default route -# defaultroute="192.168.0.1" +#defaultroute="192.168.0.1" # Lastly, the interfaces variable pulls in virtual interfaces that cannot -# be automatically detected. +# be automatically detected. +#interfaces="br0 bond0 vlan0" # You can also use files instead of variables here if you like: # /etc/ifconfig.eth0 is equivalent to ifconfig_eth0 |