# Assign static IP addresses and run custom scripts per interface.
# Seperate commands with ;
# Prefix with ! to run a shell script.
# Use \$int to represent the interface
#ifconfig_eth0="192.168.0.10 netmask 255.255.255.0"

# You also have ifup_eth0 and ifdown_eth0 to run other commands when
# eth0 is started and stopped.
# You should note that we don't stop the network at system shutdown by default.
# If you really need this, then set keep_network=NO

# Lastly, the interfaces variable pulls in virtual interfaces that cannot
# be automatically detected.
#interfaces="br0 bond0 vlan0"

# You can also use files instead of variables here if you like:
# /etc/ifconfig.eth0 is equivalent to ifconfig_eth0
# /etc/ip.eth0 is equivalent to ifconfig_eth0
# /etc/ifup.eth0 is equivalent to ifup_eth0
# /etc/ifdown.eth0 is equivalent to ifdown_eth0
# Any files found will automatically be put into the interfaces variable.
# You don't need to escape variables in files, so use $int instead of \$int.

# If you require DHCP, you should install dhcpcd and add it to the boot or
# default runlevel.

# NIS users can set the domain name here
#domainname="foobar"

# You can add a default route.
# The way this is done is slightly different depending on the operating system.
#
# *BSD:
#defaultroute="192.168.0.1"
#defaultroute6="2001:a:b:c"
#Hurd/Linux (ifconfig):
#defaultroute="gw 192.168.0.1"
#defaultroute6="gw 2001:a:b:c"

# The remainder of this file applies to Linux only and shows how
# iproute2 is supported along with other examples.

# ifconfig under Linux is not that powerful and doesn't easily handle
# multiple addresses
# On the other hand, iproute2 is quite powerful and is also supported
#ip_eth0="192.168.0.10/24; 192.168.10.10/24"

# You can also use iproute2 to add the default route.
#defaultiproute="via 192.168.0.1"
#defaultiproute6="via 2001:a:b:c"

# ip doesn't handle MTU like ifconfig, but we can do it like so
#ifup_eth0="ip link set \$int mtu 1500"

# Create a bonded interface
#interfaces="bond0"
#ifup_bond0="modprobe bonding; ifconfig \$int up; ifenslave \$int bge0"
#ifconfig_bond0="192.168.0.10 netmask 255.255.255.0"
#ifdown_bond0="rmmod bonding"

# Create tap interface and a bridge interface.
# We add the tap to the bridge.
# An external program, like dhcpcd, will configure the IP on the bridge
#interfaces="tun0 br0"
#ifup_tun0="tunctl -t \$int"
#ifdown_tun0="tunctl -d \$int"
#ifup_br0="brctl addbr \$int; brctl add \$int eth1; brtctl add \$int eth2"
#ifdown_br0="ifconfig \$int down; btctl delbr \$int"

# Create VLAN
#interfaces="eth0_2 eth0_3 eth0_4"
#ifup_eth0="vconfig add \$int 2; vconfig add \$int 3; vconfig add \$int 4"
#ifconfig_eth0_2="192.168.2.10 netmask 255.255.255.0"
#ifconfig_eth0_3="192.168.3.10 netmask 255.255.255.0"
#ifconfig_eth0_4="192.168.4.10 netmask 255.255.255.0"
#ifdown_eth0="vconfig rem \$int.2; vconfig rem \$int.3; vconfig rem \$int.4"

# Normally you would use wpa_supplicant to configure wireless, but you can
# use iwconfig also
#ifup_wlan0="iwconfig \$int key s:secretkey enc open essid foobar"