From 0ddc38960c41bd36e0f455201466b696f810c04e Mon Sep 17 00:00:00 2001 From: Roy Marples Date: Sat, 29 Dec 2007 17:25:00 +0000 Subject: Move net.example to /usr/share/doc/openrc --- conf.d.BSD/net.example | 430 ------------------------------------------------- 1 file changed, 430 deletions(-) delete mode 100644 conf.d.BSD/net.example (limited to 'conf.d.BSD') diff --git a/conf.d.BSD/net.example b/conf.d.BSD/net.example deleted file mode 100644 index 31d61055..00000000 --- a/conf.d.BSD/net.example +++ /dev/null @@ -1,430 +0,0 @@ -############################################################################## -# QUICK-START -# -# The quickest start is if you want to use DHCP. -# In that case, everything should work out of the box, no configuration -# necessary, though the startup script will warn you that you haven't -# specified anything. - -# WARNING :- some examples have a mixture of IPv4 (ie 192.168.0.1) and IPv6 -# (ie 4321:0:1:2:3:4:567:89ab) internet addresses. They only work if you have -# the relevant kernel option enabled. So if you don't have an IPv6 enabled -# kernel then remove the IPv6 address from your config. - -# If you want to use a static address or use DHCP explicitly, jump -# down to the section labelled INTERFACE HANDLERS. -# -# If you want to do anything more fancy, you should take the time to -# read through the rest of this file. - -############################################################################## -# MODULES -# -# We now support modular networking scripts which means we can easily -# add support for new interface types and modules while keeping -# compatability with existing ones. -# -# Modules load by default if the package they need is installed. If -# you specify a module here that doesn't have it's package installed -# then you get an error stating which package you need to install. -# Ideally, you only use the modules setting when you have two or more -# packages installed that supply the same service. -# -# In other words, you probably should DO NOTHING HERE... - -############################################################################## -# INTERFACE HANDLERS - -# For a static configuration, use something like this -#config_eth0="192.168.0.2/24" - -# If you need more than one address, you can use something like this -# NOTE: ifconfig creates an aliased device for each extra IPv4 address -# (eth0:1, eth0:2, etc) -# iproute2 does not do this as there is no need to -#config_eth0="192.168.0.2/24 192.168.0.3/24 192.168.0.4/24" -# Or you can use sequence expressions -#config_eth0="192.168.0.{2..4}/24" FIXME - may not work with baselayout2 -# which does the same as above. Be careful though as if you use this and -# fallbacks, you have to ensure that both end up with the same number of -# values otherwise your fallback won't work correctly. - -# You can also use IPv6 addresses -# (you should always specify a prefix length with IPv6 here) -#config_eth0="192.168.0.2/24 4321:0:1:2:3:4:567:89ab/64 4321:0:1:2:3:4:567:89ac/64" - -# If you wish to keep existing addresses + routing and the interface is up, -# you can specify a noop (no operation). If the interface is down or there -# are no addresses assigned, then we move onto the next step (default dhcp) -# This is useful when configuring your interface with a kernel command line -# or similar -#config_eth0="noop 192.168.0.2/24" - -# If you don't want ANY address (only useful when calling for advanced stuff) -#config_eth0="null" - -# Here's how to do routing if you need it -# We add an IPv4 default route, IPv4 subnet route and an IPv6 unicast route -#routes_eth0="default via 192.168.0.1 -#10.0.0.0/8 via 192.168.0.1 -#::/0" - -# If a specified module fails (like dhcp - see below), you can specify a -# fallback like so -#fallback_eth0="192.168.0.2 netmask 255.255.255.0" -#fallback_route_eth0="default via 192.168.0.1" - -# NOTE: fallback entry must match the entry location in config_eth0 -# As such you can only have one fallback route. - -# Some users may need to alter the MTU - here's how -#mtu_eth0="1500" - -# Most drivers that report carrier status function correctly, but some do not -# One of these faulty drivers is for the Intel e1000 network card, but only -# at boot time. To get around this you may alter the carrier_timeout value for -# the interface. -1 is disable, 0 is infinite and any other number of seconds -# is how long we wait for carrier. The current default is 3 seconds -#carrier_timeout_eth0=-1 - -############################################################################## -# OPTIONAL MODULES - -#----------------------------------------------------------------------------- -# WIRELESS (802.11 support) -# Wireless can be provided by BSDs ifconfig (iwconfig) or wpa_supplicant -# wpa_supplicant is preferred, use the modules directive to prefer iwconfig. -#modules="iwconfig" - -# ifconfig (iwconig) support is a one shot script - wpa_supplicant is daemon -# that scans, assoicates and re-configures if assocation is lost. -# We call it iwconfig to seperate the wireless setup from ifconfig. -#################################### -# HINTS -# -# Most users will just need to set the following options -# key_SSID1="s:yourkeyhere enc open" # s: means a text key -# key_SSID2="aaaa-bbbb-cccc-dd" # no s: means a hex key -# preferred_aps="SSID1 SSID2" -# -# Clear? Good. Now configure your wireless network below - -#################################### -# SETTINGS -# Hard code an SSID to an interface - leave this unset if you wish the driver -# to scan for available Access Points -# I would only set this as a last resort really - use the preferred_aps -# setting at the bottom of this file -#essid_eth0='foo' - -# Some drivers/hardware don't scan all that well. We have no control over this -# but we can say how many scans we want to do to try and get a better sweep of -# the area. The default is 1. -#scans_eth0="1" - -#Channel can be set (1-14), but defaults to 3 if not set. -# -# The below is taken verbatim from the BSD wavelan documentation found at -# http://www.netbsd.org/Documentation/network/wavelan.html -# There are 14 channels possible; We are told that channels 1-11 are legal for -# North America, channels 1-13 for most of Europe, channels 10-13 for France, -# and only channel 14 for Japan. If in doubt, please refer to the documentation -# that came with your card or access point. Make sure that the channel you -# select is the same channel your access point (or the other card in an ad-hoc -# network) is on. The default for cards sold in North America and most of Europe -# is 3; the default for cards sold in France is 11, and the default for cards -# sold in Japan is 14. -#channel_eth0="3" - -# Setup any other config commands. This is basically the ifconfig argument -# without the ifconfig $iface. -#ifconfig_eth0="" -# You can do the same per SSID too. -#ifconfig_SSID="" - -# Seconds to wait until associated. The default is to wait 10 seconds. -# 0 means wait indefinitely. WARNING: this can cause an infinite delay when -# booting. -#associate_timeout_eth0="5" - -# Define a WEP key per SSID or MAC address (of the AP, not your card) -# The encryption type (open or restricted) must match the -# encryption type on the Access Point. -# To set a hex key, prefix with 0x -#key_SSID="0x12341234123412341234123456" -# or you can use strings. Passphrase IS NOT supported -#key_SSID="foobar" -#key_SSID="foobar" - -# WEP key for the AP with MAC address 001122334455 -#mac_key_001122334455="foobar" - -# You can also override the interface settings found in /etc/conf.d/net -# per SSID - which is very handy if you use different networks a lot -#config_SSID="dhcp" -#routes_SSID= -#fallback_SSID= - -# Setting name/domain server causes /etc/resolv.conf to be overwritten -# Note that if DHCP is used, and you want this to take precedence then -# please put -R in your dhcpcd options -#dns_servers_SSID="192.168.0.1 192.168.0.2" -#dns_domain_SSID="some.domain" -#dns_search_SSID="search.this.domain search.that.domain" -# Please check the man page for resolv.conf for more information -# as domain and search (searchdomains) are mutually exclusive and -# searchdomains takes precedence - -# You can also set any of the /etc/conf.d/net variables per MAC address -# incase you use Access Points with the same SSID but need different -# networking configs. Below is an example - of course you use the same -# method with other variables -#config_001122334455="dhcp" -#dns_servers_001122334455="192.168.0.1 192.168.0.2" - -# Map a MAC address to an SSID -# This is used when the Access Point is not broadcasting it's SSID -# WARNING: This will override the SSID being broadcast due to some -# Access Points sending an SSID even when they have been configured -# not to! -# Change 001122334455 to the MAC address and SSID to the SSID -# it should map to -#mac_essid_001122334455="SSID" - -# This lists the preferred SSIDs to connect to in order -# SSID's can contain any characters here as they must match the broadcast -# SSID exactly. -# Surround each SSID with the " character and seperate them with a space -# If the first SSID isn't found then it moves onto the next -# If this isn't defined then it connects to the first one found -#preferred_aps="SSID1 SSID2" - -# You can also define a preferred_aps list per interface -#preferred_aps_eth0="SSID3 SSID4" - -# You can also say whether we only connect to preferred APs or not -# Values are "any", "preferredonly", "forcepreferred", "forcepreferredonly" -# and "forceany" -# "any" means it will connect to visible APs in the preferred list and then -# any other available AP -# "preferredonly" means it will only connect to visible APs in the preferred -# list -# "forcepreferred" means it will forceably connect to APs in order if it does -# not find them in a scan -# "forcepreferredonly" means it forceably connects to the APs in order and -# does not bother to scan -# "forceany" does the same as forcepreferred + connects to any other -# available AP -# Default is "any" -#associate_order="any" -#associate_order_eth0="any" - -# You can define blacklisted Access Points in the same way -#blacklist_aps="SSID1 SSID2" -#blacklist_aps_eth0="SSID3 SSID4" - -# If you have more than one wireless card, you can say if you want -# to allow each card to associate with the same Access Point or not -# Values are "yes" and "no" -# Default is "yes" -#unique_ap="yes" -#unique_ap_eth0="yes" - -# IMPORTANT: preferred_only, blacklisted_aps and unique_ap only work when -# essid_eth0 is not set and your card is capable of scanning - -# NOTE: preferred_aps list ignores blacklisted_aps - so if you have -# the same SSID in both, well, you're a bit silly :p - -################################################## -# wpa_supplicant -# emerge net-wireless/wpa-supplicant -# Wireless options are held in /etc/wpa_supplicant/wpa_supplicant.conf -# Console the wpa_supplicant.conf.example that is installed in -# /usr/share/doc/wpa_supplicant - -# By default we don't wait for wpa_suppliant to associate and authenticate. -# If you would like to, so can specify how long in seconds -#associate_timeout_eth0=60 -# A value of 0 means wait forever. - -# You can also override any settings found here per SSID - which is very -# handy if you use different networks a lot. See below for using the SSID -# in our variables -#config_SSID="dhcp" -# See the System module below for setting dns/nis/ntp per SSID - -# You can also override any settings found here per MAC address of the AP -# in case you use Access Points with the same SSID but need different -# networking configs. Below is an example - of course you use the same -# method with other variables -#mac_config_001122334455="dhcp" -#mac_dns_servers_001122334455="192.168.0.1 192.168.0.2" - -# When an interface has been associated with an Access Point, a global -# variable called SSID is set to the Access Point's SSID for use in the -# pre/post user functions below (although it's not available in preup as you -# won't have associated then) - -# If you're using anything else to configure wireless on your interface AND -# you have installed wpa_supplicant, you need to disable wpa_supplicant -#modules="!iwconfig !wpa_supplicant" -#or -#modules="!wireless" - -############################################################################## -# WIRELESS SSID IN VARIABLES -############################################################################## -# Remember to change SSID to your SSID. -# Say that your SSID is My NET - the line -# #key_SSID="s:passkey" -# becomes -# #key_My_NET="s:passkey" -# Notice that the space has changed to an underscore - do the same with all -# characters not in a-z A-Z (English alphabet) 0-9. This only applies to -# variables and not values. -# -# Any SSID's in values like essid_eth0="My NET" may need to be escaped -# This means placing the character \ before the character -# \" need to be escaped for example -# So if your SSID is -# My "\ NET -# it becomes -# My \"\\ NET -# for example -# #essid_eth0="My\"\\NET" -# -# So using the above we can use -# #dns_domain_My____NET="My\"\\NET" -# which is an invalid dns domain, but shows the how to use the variable -# structure -######################################################### - -#----------------------------------------------------------------------------- -# DHCP -# DHCP can be provided by dhclient. -# -# dhcpcd: emerge net-misc/dhcpcd -# dhclient: emerge net-misc/dhcp - -# Regardless of which DHCP client you prefer, you configure them the -# same way using one of following depending on which interface modules -# you're using. -#config_eth0="dhcp" - -# For passing custom options to dhcpcd use something like the following. This -# example reduces the timeout for retrieving an address from 60 seconds (the -# default) to 10 seconds. -#dhcpcd_eth0="-t 10" - -# GENERIC DHCP OPTIONS -# Set generic DHCP options like so -#dhcp_eth0="release nodns nontp nonis nogateway nosendhost" - -# This tells the dhcp client to release it's lease when it stops, not to -# overwrite dns, ntp and nis settings, not to set a default route and not to -# send the current hostname to the dhcp server and when it starts. -# You can use any combination of the above options - the default is not to -# use any of them. - - -#----------------------------------------------------------------------------- -# System -# For configuring system specifics such as domain, dns, ntp and nis servers -# It's rare that you would need todo this, but you can anyway. -# This is most benefit to wireless users who don't use DHCP so they can change -# their configs based on SSID. - -# If you omit the _eth0 suffix, then it applies to all interfaces unless -# overridden by the interface suffix. -#dns_domain_eth0="your.domain" -#dns_servers_eth0="192.168.0.2 192.168.0.3" -#dns_search_eth0="this.domain that.domain" -#dns_options_eth0="timeout:1 rotate" -#dns_sortlist_eth0="130.155.160.0/255.255.240.0 130.155.0.0" -# See the man page for resolv.conf for details about the options and sortlist -# directives - -#ntp_servers_eth0="192.168.0.2 192.168.0.3" - -#nis_domain_eth0="domain" -#nis_servers_eth0="192.168.0.2 192.168.0.3" - -# NOTE: Setting any of these will stamp on the files in question. So if you -# don't specify dns_servers but you do specify dns_domain then no nameservers -# will be listed in /etc/resolv.conf even if there were any there to start -# with. -# If this is an issue for you then maybe you should look into a resolv.conf -# manager like resolvconf-gentoo to manage this file for you. All packages -# that baselayout supports use resolvconf-gentoo if installed. - -#----------------------------------------------------------------------------- -# Cable in/out detection -# Sometimes the cable is in, others it's out. Obviously you don't want to -# restart net.eth0 every time when you plug it in either. -# BSD has the Device State Change Daemon - or devd for short -# To enable this, simple add devd to the boot runlevel -#rc-update add devd boot -#rc - -############################################################################## -# ADVANCED CONFIGURATION -# -# Four functions can be defined which will be called surrounding the -# start/stop operations. The functions are called with the interface -# name first so that one function can control multiple adapters. An extra two -# functions can be defined when an interface fails to start or stop. -# -# The return values for the preup and predown functions should be 0 -# (success) to indicate that configuration or deconfiguration of the -# interface can continue. If preup returns a non-zero value, then -# interface configuration will be aborted. If predown returns a -# non-zero value, then the interface will not be allowed to continue -# deconfiguration. -# -# The return values for the postup, postdown, failup and faildown functions are -# ignored since there's nothing to do if they indicate failure. -# -# ${IFACE} is set to the interface being brought up/down -# ${IFVAR} is ${IFACE} converted to variable name bash allows - -#preup() { -# # Remember to return 0 on success -# return 0 -#} - -#predown() { -# # The default in the script is to test for NFS root and disallow -# # downing interfaces in that case. Note that if you specify a -# # predown() function you will override that logic. Here it is, in -# # case you still want it... -# if is_net_fs /; then -# eerror "root filesystem is network mounted -- can't stop ${IFACE}" -# return 1 -# fi -# -# # Remember to return 0 on success -# return 0 -#} - -#postup() { -# # This function could be used, for example, to register with a -# # dynamic DNS service. Another possibility would be to -# # send/receive mail once the interface is brought up. - -#} - -#postdown() { -# # Return 0 always -# return 0 -#} - -#failup() { -# # This function is mostly here for completeness... I haven't -# # thought of anything nifty to do with it yet ;-) -#} - -#faildown() { -# # This function is mostly here for completeness... I haven't -# # thought of anything nifty to do with it yet ;-) -#} -- cgit v1.2.3