diff options
Diffstat (limited to 'conf.d.BSD')
| -rw-r--r-- | conf.d.BSD/Makefile | 2 | ||||
| -rw-r--r-- | conf.d.BSD/net.example | 139 | ||||
| -rw-r--r-- | conf.d.BSD/wireless.example | 190 |
3 files changed, 139 insertions, 192 deletions
diff --git a/conf.d.BSD/Makefile b/conf.d.BSD/Makefile index 13731e61..29aa2212 100644 --- a/conf.d.BSD/Makefile +++ b/conf.d.BSD/Makefile @@ -1,5 +1,5 @@ DIR = /etc/conf.d -FILES = localmount net.example wireless.example +FILES = localmount net.example TOPDIR = .. include $(TOPDIR)/default.mk diff --git a/conf.d.BSD/net.example b/conf.d.BSD/net.example index 7108c0f6..2d80c873 100644 --- a/conf.d.BSD/net.example +++ b/conf.d.BSD/net.example @@ -111,8 +111,145 @@ # ifconfig support is a one shot script - wpa_supplicant is daemon that # scans, assoicates and re-configures if assocation is lost. # wpa_supplicant is preferred -# See wireless.example for details about using ifconfig for wireless +#################################### +# HINTS +# +# Most users will just need to set the following options +# key_ESSID1="s:yourkeyhere enc open" # s: means a text key +# key_ESSID2="aaaa-bbbb-cccc-dd" # no s: means a hex key +# preferred_aps="'ESSID1' 'ESSID2'" +# +# Clear? Good. Now configure your wireless network below + +#################################### +# SETTINGS +# Hard code an ESSID to an interface - leave this unset if you wish the driver +# to scan for available Access Points +# I would only set this as a last resort really - use the preferred_aps +# setting at the bottom of this file +#essid_eth0='foo' + +# Some drivers/hardware don't scan all that well. We have no control over this +# but we can say how many scans we want to do to try and get a better sweep of +# the area. The default is 1. +#scans_eth0="1" + +#Channel can be set (1-14), but defaults to 3 if not set. +# +# The below is taken verbatim from the BSD wavelan documentation found at +# http://www.netbsd.org/Documentation/network/wavelan.html +# There are 14 channels possible; We are told that channels 1-11 are legal for +# North America, channels 1-13 for most of Europe, channels 10-13 for France, +# and only channel 14 for Japan. If in doubt, please refer to the documentation +# that came with your card or access point. Make sure that the channel you +# select is the same channel your access point (or the other card in an ad-hoc +# network) is on. The default for cards sold in North America and most of Europe +# is 3; the default for cards sold in France is 11, and the default for cards +# sold in Japan is 14. +#channel_eth0="3" + +# Setup any other config commands. This is basically the ifconfig argument +# without the ifconfig $iface. +#ifconfig_eth0="" +# You can do the same per ESSID too. +#ifconfig_ESSID="" + +# Seconds to wait until associated. The default is to wait 10 seconds. +# 0 means wait indefinitely. WARNING: this can cause an infinite delay when +# booting. +#associate_timeout_eth0="5" + +# Define a WEP key per ESSID or MAC address (of the AP, not your card) +# The encryption type (open or restricted) must match the +# encryption type on the Access Point. +# To set a hex key, prefix with 0x +#key_ESSID="0x12341234123412341234123456" +# or you can use strings. Passphrase IS NOT supported +#key_ESSID="foobar" +#key_ESSID="foobar" + +# WEP key for the AP with MAC address 001122334455 +#mac_key_001122334455="foobar" + +# You can also override the interface settings found in /etc/conf.d/net +# per ESSID - which is very handy if you use different networks a lot +#config_ESSID="dhcp" +#routes_ESSID= +#fallback_ESSID= +# Setting name/domain server causes /etc/resolv.conf to be overwritten +# Note that if DHCP is used, and you want this to take precedence then +# please put -R in your dhcpcd options +#dns_servers_ESSID="192.168.0.1 192.168.0.2" +#dns_domain_ESSID="some.domain" +#dns_search_path_ESSID="search.this.domain search.that.domain" +# Please check the man page for resolv.conf for more information +# as domain and search (searchdomains) are mutually exclusive and +# searchdomains takes precedence + +# You can also set any of the /etc/conf.d/net variables per MAC address +# incase you use Access Points with the same ESSID but need different +# networking configs. Below is an example - of course you use the same +# method with other variables +#config_001122334455="dhcp" +#dns_servers_001122334455="192.168.0.1 192.168.0.2" + +# Map a MAC address to an ESSID +# This is used when the Access Point is not broadcasting it's ESSID +# WARNING: This will override the ESSID being broadcast due to some +# Access Points sending an ESSID even when they have been configured +# not to! +# Change 001122334455 to the MAC address and ESSID to the ESSID +# it should map to +#mac_essid_001122334455="ESSID" + +# This lists the preferred ESSIDs to connect to in order +# ESSID's can contain any characters here as they must match the broadcast +# ESSID exactly. +# Surround each ESSID with the " character and seperate them with a space +# If the first ESSID isn't found then it moves onto the next +# If this isn't defined then it connects to the first one found +#preferred_aps="'ESSID 1' 'ESSID 2'" + +# You can also define a preferred_aps list per interface +#preferred_aps_eth0="'ESSID 3' 'ESSID 4'" + +# You can also say whether we only connect to preferred APs or not +# Values are "any", "preferredonly", "forcepreferred", "forcepreferredonly" +# and "forceany" +# "any" means it will connect to visible APs in the preferred list and then +# any other available AP +# "preferredonly" means it will only connect to visible APs in the preferred +# list +# "forcepreferred" means it will forceably connect to APs in order if it does +# not find them in a scan +# "forcepreferredonly" means it forceably connects to the APs in order and +# does not bother to scan +# "forceany" does the same as forcepreferred + connects to any other +# available AP +# Default is "any" +#associate_order="any" +#associate_order_eth0="any" + +# You can define blacklisted Access Points in the same way +#blacklist_aps="'ESSID 1' 'ESSID 2'" +#blacklist_aps_eth0="'ESSID 3' 'ESSID 4'" + +# If you have more than one wireless card, you can say if you want +# to allow each card to associate with the same Access Point or not +# Values are "yes" and "no" +# Default is "yes" +#unique_ap="yes" +#unique_ap_eth0="yes" + +# IMPORTANT: preferred_only, blacklisted_aps and unique_ap only work when +# essid_eth0 is not set and your card is capable of scanning + +# NOTE: preferred_aps list ignores blacklisted_aps - so if you have +# the same ESSID in both, well, you're a bit silly :p + +################################################## +# wpa_supplicant # emerge net-wireless/wpa-supplicant # Wireless options are held in /etc/wpa_supplicant/wpa_supplicant.conf # Console the wpa_supplicant.conf.example that is installed in diff --git a/conf.d.BSD/wireless.example b/conf.d.BSD/wireless.example deleted file mode 100644 index d9dadcbe..00000000 --- a/conf.d.BSD/wireless.example +++ /dev/null @@ -1,190 +0,0 @@ -# /etc/conf.d/wireless: -# Global wireless config file for net.* rc-scripts - -############################################################################## -# HINTS -############################################################################## -# see net.example for using ESSID in variable names -# -# Most users will just need to set the following options -# key_ESSID1="s:yourkeyhere enc open" # s: means a text key -# key_ESSID2="aaaa-bbbb-cccc-dd" # no s: means a hex key -# preferred_aps="'ESSID1' 'ESSID2'" -# -# Clear? Good. Now configure your wireless network below -############################################################################# - -############################################################################## -# SETTINGS -############################################################################## -# Hard code an ESSID to an interface - leave this unset if you wish the driver -# to scan for available Access Points -# I would only set this as a last resort really - use the preferred_aps -# setting at the bottom of this file -#essid_eth0='foo' - -# Some drivers/hardware don't scan all that well. We have no control over this -# but we can say how many scans we want to do to try and get a better sweep of -# the area. The default is 1. -#scans_eth0="1" - -#Channel can be set (1-14), but defaults to 3 if not set. -# -# The below is taken verbatim from the BSD wavelan documentation found at -# http://www.netbsd.org/Documentation/network/wavelan.html -# There are 14 channels possible; We are told that channels 1-11 are legal for -# North America, channels 1-13 for most of Europe, channels 10-13 for France, -# and only channel 14 for Japan. If in doubt, please refer to the documentation -# that came with your card or access point. Make sure that the channel you -# select is the same channel your access point (or the other card in an ad-hoc -# network) is on. The default for cards sold in North America and most of Europe -# is 3; the default for cards sold in France is 11, and the default for cards -# sold in Japan is 14. -#channel_eth0="3" - -# Setup any other config commands. This is basically the ifconfig argument -# without the ifconfig $iface. -#ifconfig_eth0="" -# You can do the same per ESSID too. -#ifconfig_ESSID="" - -# Seconds to wait until associated. The default is to wait 10 seconds. -# 0 means wait indefinitely. WARNING: this can cause an infinite delay when -# booting. -#associate_timeout_eth0="5" - -# Define a WEP key per ESSID or MAC address (of the AP, not your card) -# The encryption type (open or restricted) must match the -# encryption type on the Access Point. -# To set a hex key, prefix with 0x -#key_ESSID="0x12341234123412341234123456" -# or you can use strings. Passphrase IS NOT supported -#key_ESSID="foobar" -#key_ESSID="foobar" - -# WEP key for the AP with MAC address 001122334455 -#mac_key_001122334455="foobar" - -# You can also override the interface settings found in /etc/conf.d/net -# per ESSID - which is very handy if you use different networks a lot -#config_ESSID="dhcp" -#routes_ESSID= -#fallback_ESSID= - -# Setting name/domain server causes /etc/resolv.conf to be overwritten -# Note that if DHCP is used, and you want this to take precedence then -# please put -R in your dhcpcd options -#dns_servers_ESSID="192.168.0.1 192.168.0.2" -#dns_domain_ESSID="some.domain" -#dns_search_path_ESSID="search.this.domain search.that.domain" -# Please check the man page for resolv.conf for more information -# as domain and search (searchdomains) are mutually exclusive and -# searchdomains takes precedence - -# You can also set any of the /etc/conf.d/net variables per MAC address -# incase you use Access Points with the same ESSID but need different -# networking configs. Below is an example - of course you use the same -# method with other variables -#config_001122334455="dhcp" -#dns_servers_001122334455="192.168.0.1 192.168.0.2" - -# Map a MAC address to an ESSID -# This is used when the Access Point is not broadcasting it's ESSID -# WARNING: This will override the ESSID being broadcast due to some -# Access Points sending an ESSID even when they have been configured -# not to! -# Change 001122334455 to the MAC address and ESSID to the ESSID -# it should map to -#mac_essid_001122334455="ESSID" - -# This lists the preferred ESSIDs to connect to in order -# ESSID's can contain any characters here as they must match the broadcast -# ESSID exactly. -# Surround each ESSID with the " character and seperate them with a space -# If the first ESSID isn't found then it moves onto the next -# If this isn't defined then it connects to the first one found -#preferred_aps="'ESSID 1' 'ESSID 2'" - -# You can also define a preferred_aps list per interface -#preferred_aps_eth0="'ESSID 3' 'ESSID 4'" - -# You can also say whether we only connect to preferred APs or not -# Values are "any", "preferredonly", "forcepreferred", "forcepreferredonly" -# and "forceany" -# "any" means it will connect to visible APs in the preferred list and then -# any other available AP -# "preferredonly" means it will only connect to visible APs in the preferred -# list -# "forcepreferred" means it will forceably connect to APs in order if it does -# not find them in a scan -# "forcepreferredonly" means it forceably connects to the APs in order and -# does not bother to scan -# "forceany" does the same as forcepreferred + connects to any other -# available AP -# Default is "any" -#associate_order="any" -#associate_order_eth0="any" - -# You can define blacklisted Access Points in the same way -#blacklist_aps="'ESSID 1' 'ESSID 2'" -#blacklist_aps_eth0="'ESSID 3' 'ESSID 4'" - -# If you have more than one wireless card, you can say if you want -# to allow each card to associate with the same Access Point or not -# Values are "yes" and "no" -# Default is "yes" -#unique_ap="yes" -#unique_ap_eth0="yes" - -# IMPORTANT: preferred_only, blacklisted_aps and unique_ap only work when -# essid_eth0 is not set and your card is capable of scanning - -# NOTE: preferred_aps list ignores blacklisted_aps - so if you have -# the same ESSID in both, well, you're a bit silly :p - - -############################################################################## -# ADVANCED CONFIGURATION -# -# Two functions can be defined which will be called surrounding the -# associate function. The functions are called with the interface -# name first so that one function can control multiple adapters. -# -# The return values for the preassociate function should be 0 -# (success) to indicate that configuration or deconfiguration of the -# interface can continue. If preassociate returns a non-zero value, then -# interface configuration will be aborted. -# -# The return value for the postassociate function is ignored -# since there's nothing to do if it indicates failure. - -#preassociate() { -# # The below adds two configuration variables leap_user_ESSID -# # and leap_pass_ESSID. When they are both confiugred for the ESSID -# # being connected to then we run the CISCO LEAP script -# -# local user pass -# eval user=\"\$\{leap_user_${ESSIDVAR}\}\" -# eval pass=\"\$\{leap_pass_${ESSIDVAR}\}\" -# -# if [ -n "${user}" -a -n "${pass}" ]; then -# if [ ! -x /opt/cisco/bin/leapscript ]; then -# eend "For LEAP support, please emerge net-misc/cisco-aironet-client-utils" -# return 1 -# fi -# einfo "Waiting for LEAP Authentication on \"${ESSID}\"" -# if /opt/cisco/bin/leapscript ${user} ${pass} | grep -q 'Login incorrect'; then -# ewarn "Login Failed for ${user}" -# return 1 -# fi -# fi -# -# return 0 -#} - -#postassociate() { -# # This function is mostly here for completeness... I haven't -# # thought of anything nifty to do with it yet ;-) -# # Return 0 always -# return 0 -#} |