merge wireless.example into net.example, #174282

6 files changed, 348 insertions, 464 deletions

diff --git a/conf.d.BSD/Makefile b/conf.d.BSD/Makefile
index 13731e61..29aa2212 100644
--- a/conf.d.BSD/Makefile
+++ b/conf.d.BSD/Makefile
@@ -1,5 +1,5 @@
 DIR = /etc/conf.d
-FILES = localmount net.example wireless.example 
+FILES = localmount net.example
 
 TOPDIR = ..
 include $(TOPDIR)/default.mk
diff --git a/conf.d.BSD/net.example b/conf.d.BSD/net.example
index 7108c0f6..2d80c873 100644
--- a/conf.d.BSD/net.example
+++ b/conf.d.BSD/net.example
@@ -111,8 +111,145 @@
 # ifconfig support is a one shot script - wpa_supplicant is daemon that
 # scans, assoicates and re-configures if assocation is lost.
 # wpa_supplicant is preferred
-# See wireless.example for details about using ifconfig for wireless
+####################################
+# HINTS
+#
+# Most users will just need to set the following options
+# key_ESSID1="s:yourkeyhere enc open" # s: means a text key
+# key_ESSID2="aaaa-bbbb-cccc-dd"      # no s: means a hex key
+# preferred_aps="'ESSID1' 'ESSID2'"
+#
+# Clear? Good. Now configure your wireless network below
+
+####################################
+# SETTINGS
+# Hard code an ESSID to an interface - leave this unset if you wish the driver
+# to scan for available Access Points
+# I would only set this as a last resort really - use the preferred_aps
+# setting at the bottom of this file
+#essid_eth0='foo'
+
+# Some drivers/hardware don't scan all that well. We have no control over this
+# but we can say how many scans we want to do to try and get a better sweep of
+# the area. The default is 1.
+#scans_eth0="1"
+
+#Channel can be set (1-14), but defaults to 3 if not set.
+#
+# The below is taken verbatim from the BSD wavelan documentation found at
+# http://www.netbsd.org/Documentation/network/wavelan.html
+# There are 14 channels possible; We are told that channels 1-11 are legal for
+# North America, channels 1-13 for most of Europe, channels 10-13 for France,
+# and only channel 14 for Japan. If in doubt, please refer to the documentation
+# that came with your card or access point. Make sure that the channel you
+# select is the same channel your access point (or the other card in an ad-hoc
+# network) is on. The default for cards sold in North America and most of Europe
+# is 3; the default for cards sold in France is 11, and the default for cards
+# sold in Japan is 14.
+#channel_eth0="3"
+
+# Setup any other config commands. This is basically the ifconfig argument
+# without the ifconfig $iface.
+#ifconfig_eth0=""
+# You can do the same per ESSID too.
+#ifconfig_ESSID=""
+
+# Seconds to wait until associated. The default is to wait 10 seconds.
+# 0 means wait indefinitely. WARNING: this can cause an infinite delay when
+# booting.
+#associate_timeout_eth0="5"
+
+# Define a WEP key per ESSID or MAC address (of the AP, not your card)
+# The encryption type (open or restricted) must match the
+# encryption type on the Access Point.
+# To set a hex key, prefix with 0x
+#key_ESSID="0x12341234123412341234123456"
+# or you can use strings. Passphrase IS NOT supported
+#key_ESSID="foobar"
+#key_ESSID="foobar"
+
+# WEP key for the AP with MAC address 001122334455
+#mac_key_001122334455="foobar"
+
+# You can also override the interface settings found in /etc/conf.d/net
+# per ESSID - which is very handy if you use different networks a lot
+#config_ESSID="dhcp"
+#routes_ESSID=
+#fallback_ESSID=
 
+# Setting name/domain server causes /etc/resolv.conf to be overwritten
+# Note that if DHCP is used, and you want this to take precedence then
+# please put -R in your dhcpcd options
+#dns_servers_ESSID="192.168.0.1 192.168.0.2"
+#dns_domain_ESSID="some.domain"
+#dns_search_path_ESSID="search.this.domain search.that.domain"
+# Please check the man page for resolv.conf for more information
+# as domain and search (searchdomains) are mutually exclusive and
+# searchdomains takes precedence
+
+# You can also set any of the /etc/conf.d/net variables per MAC address
+# incase you use Access Points with the same ESSID but need different
+# networking configs. Below is an example - of course you use the same
+# method with other variables
+#config_001122334455="dhcp"
+#dns_servers_001122334455="192.168.0.1 192.168.0.2"
+
+# Map a MAC address to an ESSID
+# This is used when the Access Point is not broadcasting it's ESSID
+# WARNING: This will override the ESSID being broadcast due to some
+# Access Points sending an ESSID even when they have been configured
+# not to!
+# Change 001122334455 to the MAC address and ESSID to the ESSID
+# it should map to
+#mac_essid_001122334455="ESSID"
+
+# This lists the preferred ESSIDs to connect to in order
+# ESSID's can contain any characters here as they must match the broadcast
+# ESSID exactly.
+# Surround each ESSID with the " character and seperate them with a space
+# If the first ESSID isn't found then it moves onto the next
+# If this isn't defined then it connects to the first one found
+#preferred_aps="'ESSID 1' 'ESSID 2'"
+
+# You can also define a preferred_aps list per interface
+#preferred_aps_eth0="'ESSID 3' 'ESSID 4'"
+
+# You can also say whether we only connect to preferred APs or not
+# Values are "any", "preferredonly", "forcepreferred", "forcepreferredonly"
+# and "forceany"
+# "any" means it will connect to visible APs in the preferred list and then
+# any other available AP
+# "preferredonly" means it will only connect to visible APs in the preferred
+# list
+# "forcepreferred" means it will forceably connect to APs in order if it does
+# not find them in a scan
+# "forcepreferredonly" means it forceably connects to the APs in order and
+# does not bother to scan
+# "forceany" does the same as forcepreferred + connects to any other 
+# available AP
+# Default is "any"
+#associate_order="any"
+#associate_order_eth0="any"
+
+# You can define blacklisted Access Points in the same way
+#blacklist_aps="'ESSID 1' 'ESSID 2'"
+#blacklist_aps_eth0="'ESSID 3' 'ESSID 4'"
+
+# If you have more than one wireless card, you can say if you want
+# to allow each card to associate with the same Access Point or not
+# Values are "yes" and "no"
+# Default is "yes"
+#unique_ap="yes"
+#unique_ap_eth0="yes"
+
+# IMPORTANT: preferred_only, blacklisted_aps and unique_ap only work when
+# essid_eth0 is not set and your card is capable of scanning
+
+# NOTE: preferred_aps  list ignores blacklisted_aps - so if you have
+# the same ESSID in both, well, you're a bit silly :p
+
+##################################################
+# wpa_supplicant
 # emerge net-wireless/wpa-supplicant
 # Wireless options are held in /etc/wpa_supplicant/wpa_supplicant.conf
 # Console the wpa_supplicant.conf.example that is installed in
diff --git a/conf.d.BSD/wireless.example b/conf.d.BSD/wireless.example
deleted file mode 100644
index d9dadcbe..00000000
--- a/conf.d.BSD/wireless.example
+++ /dev/null
@@ -1,190 +0,0 @@
-# /etc/conf.d/wireless:
-# Global wireless config file for net.* rc-scripts
-
-##############################################################################
-# HINTS
-##############################################################################
-# see net.example for using ESSID in variable names
-#
-# Most users will just need to set the following options
-# key_ESSID1="s:yourkeyhere enc open" # s: means a text key
-# key_ESSID2="aaaa-bbbb-cccc-dd"      # no s: means a hex key
-# preferred_aps="'ESSID1' 'ESSID2'"
-#
-# Clear? Good. Now configure your wireless network below
-#############################################################################
-
-##############################################################################
-# SETTINGS
-##############################################################################
-# Hard code an ESSID to an interface - leave this unset if you wish the driver
-# to scan for available Access Points
-# I would only set this as a last resort really - use the preferred_aps
-# setting at the bottom of this file
-#essid_eth0='foo'
-
-# Some drivers/hardware don't scan all that well. We have no control over this
-# but we can say how many scans we want to do to try and get a better sweep of
-# the area. The default is 1.
-#scans_eth0="1"
-
-#Channel can be set (1-14), but defaults to 3 if not set.
-#
-# The below is taken verbatim from the BSD wavelan documentation found at
-# http://www.netbsd.org/Documentation/network/wavelan.html
-# There are 14 channels possible; We are told that channels 1-11 are legal for
-# North America, channels 1-13 for most of Europe, channels 10-13 for France,
-# and only channel 14 for Japan. If in doubt, please refer to the documentation
-# that came with your card or access point. Make sure that the channel you
-# select is the same channel your access point (or the other card in an ad-hoc
-# network) is on. The default for cards sold in North America and most of Europe
-# is 3; the default for cards sold in France is 11, and the default for cards
-# sold in Japan is 14.
-#channel_eth0="3"
-
-# Setup any other config commands. This is basically the ifconfig argument
-# without the ifconfig $iface.
-#ifconfig_eth0=""
-# You can do the same per ESSID too.
-#ifconfig_ESSID=""
-
-# Seconds to wait until associated. The default is to wait 10 seconds.
-# 0 means wait indefinitely. WARNING: this can cause an infinite delay when
-# booting.
-#associate_timeout_eth0="5"
-
-# Define a WEP key per ESSID or MAC address (of the AP, not your card)
-# The encryption type (open or restricted) must match the
-# encryption type on the Access Point.
-# To set a hex key, prefix with 0x
-#key_ESSID="0x12341234123412341234123456"
-# or you can use strings. Passphrase IS NOT supported
-#key_ESSID="foobar"
-#key_ESSID="foobar"
-
-# WEP key for the AP with MAC address 001122334455
-#mac_key_001122334455="foobar"
-
-# You can also override the interface settings found in /etc/conf.d/net
-# per ESSID - which is very handy if you use different networks a lot
-#config_ESSID="dhcp"
-#routes_ESSID=
-#fallback_ESSID=
-
-# Setting name/domain server causes /etc/resolv.conf to be overwritten
-# Note that if DHCP is used, and you want this to take precedence then
-# please put -R in your dhcpcd options
-#dns_servers_ESSID="192.168.0.1 192.168.0.2"
-#dns_domain_ESSID="some.domain"
-#dns_search_path_ESSID="search.this.domain search.that.domain"
-# Please check the man page for resolv.conf for more information
-# as domain and search (searchdomains) are mutually exclusive and
-# searchdomains takes precedence
-
-# You can also set any of the /etc/conf.d/net variables per MAC address
-# incase you use Access Points with the same ESSID but need different
-# networking configs. Below is an example - of course you use the same
-# method with other variables
-#config_001122334455="dhcp"
-#dns_servers_001122334455="192.168.0.1 192.168.0.2"
-
-# Map a MAC address to an ESSID
-# This is used when the Access Point is not broadcasting it's ESSID
-# WARNING: This will override the ESSID being broadcast due to some
-# Access Points sending an ESSID even when they have been configured
-# not to!
-# Change 001122334455 to the MAC address and ESSID to the ESSID
-# it should map to
-#mac_essid_001122334455="ESSID"
-
-# This lists the preferred ESSIDs to connect to in order
-# ESSID's can contain any characters here as they must match the broadcast
-# ESSID exactly.
-# Surround each ESSID with the " character and seperate them with a space
-# If the first ESSID isn't found then it moves onto the next
-# If this isn't defined then it connects to the first one found
-#preferred_aps="'ESSID 1' 'ESSID 2'"
-
-# You can also define a preferred_aps list per interface
-#preferred_aps_eth0="'ESSID 3' 'ESSID 4'"
-
-# You can also say whether we only connect to preferred APs or not
-# Values are "any", "preferredonly", "forcepreferred", "forcepreferredonly"
-# and "forceany"
-# "any" means it will connect to visible APs in the preferred list and then
-# any other available AP
-# "preferredonly" means it will only connect to visible APs in the preferred
-# list
-# "forcepreferred" means it will forceably connect to APs in order if it does
-# not find them in a scan
-# "forcepreferredonly" means it forceably connects to the APs in order and
-# does not bother to scan
-# "forceany" does the same as forcepreferred + connects to any other 
-# available AP
-# Default is "any"
-#associate_order="any"
-#associate_order_eth0="any"
-
-# You can define blacklisted Access Points in the same way
-#blacklist_aps="'ESSID 1' 'ESSID 2'"
-#blacklist_aps_eth0="'ESSID 3' 'ESSID 4'"
-
-# If you have more than one wireless card, you can say if you want
-# to allow each card to associate with the same Access Point or not
-# Values are "yes" and "no"
-# Default is "yes"
-#unique_ap="yes"
-#unique_ap_eth0="yes"
-
-# IMPORTANT: preferred_only, blacklisted_aps and unique_ap only work when
-# essid_eth0 is not set and your card is capable of scanning
-
-# NOTE: preferred_aps  list ignores blacklisted_aps - so if you have
-# the same ESSID in both, well, you're a bit silly :p
-
-
-##############################################################################
-# ADVANCED CONFIGURATION
-# 
-# Two functions can be defined which will be called surrounding the
-# associate function.  The functions are called with the interface
-# name first so that one function can control multiple adapters.
-#
-# The return values for the preassociate function should be 0
-# (success) to indicate that configuration or deconfiguration of the
-# interface can continue.  If preassociate returns a non-zero value, then
-# interface configuration will be aborted.
-#
-# The return value for the postassociate function is ignored
-# since there's nothing to do if it indicates failure.
-
-#preassociate() {
-#	# The below adds two configuration variables leap_user_ESSID
-#	# and leap_pass_ESSID. When they are both confiugred for the ESSID
-#	# being connected to then we run the CISCO LEAP script
-#
-#	local user pass
-#	eval user=\"\$\{leap_user_${ESSIDVAR}\}\"
-#	eval pass=\"\$\{leap_pass_${ESSIDVAR}\}\"
-#
-#	if [ -n "${user}" -a -n "${pass}" ]; then
-#		if [ ! -x /opt/cisco/bin/leapscript ]; then
-#			eend "For LEAP support, please emerge net-misc/cisco-aironet-client-utils"
-#			return 1
-#		fi
-#		einfo "Waiting for LEAP Authentication on \"${ESSID}\""
-#		if /opt/cisco/bin/leapscript ${user} ${pass} | grep -q 'Login incorrect'; then
-#			ewarn "Login Failed for ${user}"
-#			return 1
-#		fi
-#	fi
-#
-#	return 0
-#}
-
-#postassociate() {
-#	# This function is mostly here for completeness... I haven't
-#	# thought of anything nifty to do with it yet ;-)
-#	# Return 0 always
-#	return 0
-#}
diff --git a/conf.d.Linux/Makefile b/conf.d.Linux/Makefile
index 6a87562d..60cd40c6 100644
--- a/conf.d.Linux/Makefile
+++ b/conf.d.Linux/Makefile
@@ -1,5 +1,5 @@
 DIR = /etc/conf.d
-FILES = net.example wireless.example
+FILES = net.example
 FILES_APPEND = clock rc
 FILES_NOEXIST = consolefont keymaps volumes
 
diff --git a/conf.d.Linux/net.example b/conf.d.Linux/net.example
index ffbece15..7244baf8 100644
--- a/conf.d.Linux/net.example
+++ b/conf.d.Linux/net.example
@@ -153,10 +153,213 @@
 
 # iwconfig
 # emerge net-wireless/wireless-tools
-# Wireless options are held in /etc/conf.d/wireless - but could be here too
-# Consult the sample file /etc/conf.d/wireless.example for instructions
-# wpa_supplicant is the default if it is installed
-
+###############################################
+# HINTS
+#
+# Most users will just need to set the following options
+# key_SSID1="s:yourkeyhere enc open" # s: means a text key
+# key_SSID2="aaaa-bbbb-cccc-dd"      # no s: means a hex key
+# preferred_aps="'SSID 1' 'SSID 2'"
+#
+# Clear? Good. Now configure your wireless network below
+
+###############################################
+# SETTINGS
+# Hard code an SSID to an interface - leave this unset if you wish the driver
+# to scan for available Access Points
+# Set to "any" to connect to any SSID - the driver picks an Access Point
+# This needs to be done when the driver doesn't support scanning
+# This may work for drivers that don't support scanning but you need automatic
+# AP association
+# I would only set this as a last resort really - use the preferred_aps
+# setting at the bottom of this file
+
+# However, using ad-hoc (without scanning for APs) and master mode
+# do require the SSID to be set - do this here
+#essid_eth0="any"
+
+# Set the mode of the interface (managed, ad-hoc, master or auto)
+# The default is auto
+# If it's ad-hoc or master you also may need to specify the channel below
+#mode_eth0="auto"
+
+# If managed mode fails, drop to ad-hoc mode with the below SSID?
+#adhoc_essid_eth0="WLAN"
+
+# Some drivers/hardware don't scan all that well. We have no control over this
+# but we can say how many scans we want to do to try and get a better sweep of
+# the area. The default is 1.
+#scans_eth0="1"
+
+#Channel can be set (1-14), but defaults to 3 if not set.
+#
+# The below is taken verbatim from the BSD wavelan documentation found at
+# http://www.netbsd.org/Documentation/network/wavelan.html
+# There are 14 channels possible; We are told that channels 1-11 are legal for
+# North America, channels 1-13 for most of Europe, channels 10-13 for France,
+# and only channel 14 for Japan. If in doubt, please refer to the documentation
+# that came with your card or access point. Make sure that the channel you
+# select is the same channel your access point (or the other card in an ad-hoc
+# network) is on. The default for cards sold in North America and most of Europe
+# is 3; the default for cards sold in France is 11, and the default for cards
+# sold in Japan is 14.
+#channel_eth0="3"
+
+# Setup any other config commands. This is basically the iwconfig argument
+# without the iwconfig $iface.
+#iwconfig_eth0=""
+
+# Set private driver ioctls. This is basically the iwpriv argument without
+# the iwpriv $iface. If you use the rt2500 driver (not the rt2x00 one) then
+# you can set WPA here, below is an example.
+#iwpriv_eth0=""
+#iwpriv_SSID=" \
+#	'set AuthMode=WPAPSK' \
+#	'set EncrypType=TKIP' \
+#	'set WPAPSK=yourpasskey' \
+#"
+#NOTE: Even though you can use WPA like so, you may have to set a WEP key
+#if your driver claims the AP is encrypted. The WEP key itself will not be
+#used though.
+
+# Seconds to wait before scanning
+# Some drivers need to wait until they have finished "loading"
+# before they can scan - otherwise they error and claim that they cannot scan
+# or resource is unavailable. The default is to wait zero seconds
+#sleep_scan_eth0="1"
+
+# Seconds to wait until associated. The default is to wait 10 seconds.
+# 0 means wait indefinitely. WARNING: this can cause an infinite delay when
+# booting.
+#associate_timeout_eth0="5"
+
+# By default a successful association in Managed mode sets the MAC
+# address of the AP connected to. However, some drivers (namely
+# the ipw2100) don't set an invalid MAC address when association
+# fails - so we need to check on link quality which some drivers
+# don't report properly either.
+# So if you have connection problems try flipping this setting
+# Valid options are MAC, quality and all - defaults to MAC
+#associate_test_eth0="MAC"
+
+# Some driver/card combinations need to scan in Ad-Hoc mode
+# After scanning, the mode is reset to the one defined above
+#scan_mode_eth0="Ad-Hoc"
+
+# Below you can define private ioctls to run before and after scanning
+# Format is the same as the iwpriv_eth0 above
+# This is needed for the HostAP drivers
+#iwpriv_scan_pre_eth0="'host_roaming 2'"
+#iwpriv_scan_post_eth0="'host_roaming 0'"
+
+# Define a WEP key per SSID or MAC address (of the AP, not your card)
+# The encryption type (open or restricted) must match the
+# encryption type on the Access Point
+# You can't use "any" for an SSID here
+#key_SSID="1234-1234-1234-1234-1234-1234-56"
+# or you can use strings. Passphrase IS NOT supported
+# To use a string, prefix it with s:
+# Note - this example also sets the encryption method to open
+# which is regarded as more secure than restricted
+#key_SSID="s:foobar enc open"
+#key_SSID="s:foobar enc restricted"
+
+# If you have whitespace in your key, here's how to set it and use other
+# commands like using open encryption.
+#key_SSID="s:'foo bar' enc open"
+
+# WEP key for the AP with MAC address 001122334455
+#mac_key_001122334455="s:foobar"
+
+# Here are some more examples of keys as some users find others work
+# and some don't where they should all do the same thing
+#key_SSID="open s:foobar"
+#key_SSID="open 1234-5678-9012"
+#key_SSID="s:foobar enc open"
+#key_SSID="1234-5678-9012 enc open"
+
+# You may want to set muliple keys - here's an example
+# It sets 4 keys on the card and instructs to use key 2 by default
+#key_SSID="[1] s:passkey1 key [2] s:passkey2 key [3] s:passkey3 key [4] s:passkey4 key [2]"
+
+# You can also override the interface settings found in /etc/conf.d/net
+# per SSID - which is very handy if you use different networks a lot
+#config_SSID="dhcp"
+#dhcpcd_SSID="-t 5"
+#routes_SSID=
+#fallback_SSID=
+
+# Setting name/domain server causes /etc/resolv.conf to be overwritten
+# Note that if DHCP is used, and you want this to take precedence then
+# please put -R in your dhcpcd options
+#dns_servers_SSID="192.168.0.1 192.168.0.2"
+#dns_domain_SSID="some.domain"
+#dns_search_path_SSID="search.this.domain search.that.domain"
+# Please check the man page for resolv.conf for more information
+# as domain and search (searchdomains) are mutually exclusive and
+# searchdomains takes precedence
+
+# You can also set any of the /etc/conf.d/net variables per MAC address
+# incase you use Access Points with the same SSID but need different
+# networking configs. Below is an example - of course you use the same
+# method with other variables
+#config_001122334455="dhcp"
+#dhcpcd_001122334455="-t 10"
+#dns_servers_001122334455="192.168.0.1 192.168.0.2"
+
+# Map a MAC address to an SSID
+# This is used when the Access Point is not broadcasting it's SSID
+# WARNING: This will override the SSID being broadcast due to some
+# Access Points sending an SSID even when they have been configured
+# not to!
+# Change 001122334455 to the MAC address and SSID to the SSID
+# it should map to
+#mac_essid_001122334455="SSID"
+
+# This lists the preferred SSIDs to connect to in order
+# SSID's can contain any characters here as they must match the broadcast
+# SSID exactly.
+# Surround each SSID with the " character and seperate them with a space
+# If the first SSID isn't found then it moves onto the next
+# If this isn't defined then it connects to the first one found
+#preferred_aps="'SSID 1' 'SSID 2'"
+
+# You can also define a preferred_aps list per interface
+#preferred_aps_eth0="'SSID 3' 'SSID 4'"
+
+# You can also say whether we only connect to preferred APs or not
+# Values are "any", "preferredonly", "forcepreferred", "forcepreferredonly" and "forceany"
+# "any" means it will connect to visible APs in the preferred list and then any
+# other available AP
+# "preferredonly" means it will only connect to visible APs in the preferred list
+# "forcepreferred" means it will forceably connect to APs in order if it does not find
+# them in a scan
+# "forcepreferredonly" means it forceably connects to the APs in order and does not bother
+# to scan
+# "forceany" does the same as forcepreferred + connects to any other available AP
+# Default is "any"
+#associate_order="any"
+#associate_order_eth0="any"
+
+# You can define blacklisted Access Points in the same way
+#blacklist_aps="'SSID 1' 'SSID 2'"
+#blacklist_aps_eth0="'SSID 3' 'SSID 4'"
+
+# If you have more than one wireless card, you can say if you want
+# to allow each card to associate with the same Access Point or not
+# Values are "yes" and "no"
+# Default is "yes"
+#unique_ap="yes"
+#unique_ap_eth0="yes"
+
+# IMPORTANT: preferred_only, blacklisted_aps and unique_ap only work when
+# essid_eth0 is not set and your card is capable of scanning
+
+# NOTE: preferred_aps  list ignores blacklisted_aps - so if you have
+# the same SSID in both, well, you're a bit silly :p
+
+
+############################################################
 # wpa_supplicant
 # emerge net-wireless/wpa-supplicant
 # Wireless options are held in /etc/wpa_supplicant/wpa_supplicant.conf
@@ -665,7 +868,7 @@
 # For configuring system specifics such as domain, dns, ntp and nis servers
 # It's rare that you would need todo this, but you can anyway.
 # This is most benefit to wireless users who don't use DHCP so they can change
-# their configs based on SSID. See wireless.example for more details
+# their configs based on SSID.
 
 # To use dns settings such as these, dns_servers_eth0 must be set!
 # If you omit the _eth0 suffix, then it applies to all interfaces unless
diff --git a/conf.d.Linux/wireless.example b/conf.d.Linux/wireless.example
deleted file mode 100644
index 7b0edd68..00000000
--- a/conf.d.Linux/wireless.example
+++ /dev/null
@@ -1,266 +0,0 @@
-# /etc/conf.d/wireless:
-# Global wireless config file for net.* rc-scripts
-
-##############################################################################
-# IMPORTANT
-# linux-wlan-ng is not supported as they have their own configuration program
-# ensure that /etc/conf.d/net has the entry "!iwconfig" in it's modules line
-# Try and use an alternative driver if you need to use this - hostap-driver
-# supports non-usb linux-wlan-ng driven devices
-##############################################################################
-
-##############################################################################
-# HINTS
-##############################################################################
-# see net.example for using SSID in variable names
-#
-# Most users will just need to set the following options
-# key_SSID1="s:yourkeyhere enc open" # s: means a text key
-# key_SSID2="aaaa-bbbb-cccc-dd"      # no s: means a hex key
-# preferred_aps="'SSID 1' 'SSID 2'"
-#
-# Clear? Good. Now configure your wireless network below
-#############################################################################
-
-##############################################################################
-# SETTINGS
-##############################################################################
-# Hard code an SSID to an interface - leave this unset if you wish the driver
-# to scan for available Access Points
-# Set to "any" to connect to any SSID - the driver picks an Access Point
-# This needs to be done when the driver doesn't support scanning
-# This may work for drivers that don't support scanning but you need automatic
-# AP association
-# I would only set this as a last resort really - use the preferred_aps
-# setting at the bottom of this file
-
-# However, using ad-hoc (without scanning for APs) and master mode
-# do require the SSID to be set - do this here
-#essid_eth0="any"
-
-# Set the mode of the interface (managed, ad-hoc, master or auto)
-# The default is auto
-# If it's ad-hoc or master you also may need to specify the channel below
-#mode_eth0="auto"
-
-# If managed mode fails, drop to ad-hoc mode with the below SSID?
-#adhoc_essid_eth0="WLAN"
-
-# Some drivers/hardware don't scan all that well. We have no control over this
-# but we can say how many scans we want to do to try and get a better sweep of
-# the area. The default is 1.
-#scans_eth0="1"
-
-#Channel can be set (1-14), but defaults to 3 if not set.
-#
-# The below is taken verbatim from the BSD wavelan documentation found at
-# http://www.netbsd.org/Documentation/network/wavelan.html
-# There are 14 channels possible; We are told that channels 1-11 are legal for
-# North America, channels 1-13 for most of Europe, channels 10-13 for France,
-# and only channel 14 for Japan. If in doubt, please refer to the documentation
-# that came with your card or access point. Make sure that the channel you
-# select is the same channel your access point (or the other card in an ad-hoc
-# network) is on. The default for cards sold in North America and most of Europe
-# is 3; the default for cards sold in France is 11, and the default for cards
-# sold in Japan is 14.
-#channel_eth0="3"
-
-# Setup any other config commands. This is basically the iwconfig argument
-# without the iwconfig $iface.
-#iwconfig_eth0=""
-
-# Set private driver ioctls. This is basically the iwpriv argument without
-# the iwpriv $iface. If you use the rt2500 driver (not the rt2x00 one) then
-# you can set WPA here, below is an example.
-#iwpriv_eth0=""
-#iwpriv_SSID=" \
-#	'set AuthMode=WPAPSK' \
-#	'set EncrypType=TKIP' \
-#	'set WPAPSK=yourpasskey' \
-#"
-#NOTE: Even though you can use WPA like so, you may have to set a WEP key
-#if your driver claims the AP is encrypted. The WEP key itself will not be
-#used though.
-
-# Seconds to wait before scanning
-# Some drivers need to wait until they have finished "loading"
-# before they can scan - otherwise they error and claim that they cannot scan
-# or resource is unavailable. The default is to wait zero seconds
-#sleep_scan_eth0="1"
-
-# Seconds to wait until associated. The default is to wait 10 seconds.
-# 0 means wait indefinitely. WARNING: this can cause an infinite delay when
-# booting.
-#associate_timeout_eth0="5"
-
-# By default a successful association in Managed mode sets the MAC
-# address of the AP connected to. However, some drivers (namely
-# the ipw2100) don't set an invalid MAC address when association
-# fails - so we need to check on link quality which some drivers
-# don't report properly either.
-# So if you have connection problems try flipping this setting
-# Valid options are MAC, quality and all - defaults to MAC
-#associate_test_eth0="MAC"
-
-# Some driver/card combinations need to scan in Ad-Hoc mode
-# After scanning, the mode is reset to the one defined above
-#scan_mode_eth0="Ad-Hoc"
-
-# Below you can define private ioctls to run before and after scanning
-# Format is the same as the iwpriv_eth0 above
-# This is needed for the HostAP drivers
-#iwpriv_scan_pre_eth0="'host_roaming 2'"
-#iwpriv_scan_post_eth0="'host_roaming 0'"
-
-# Define a WEP key per SSID or MAC address (of the AP, not your card)
-# The encryption type (open or restricted) must match the
-# encryption type on the Access Point
-# You can't use "any" for an SSID here
-#key_SSID="1234-1234-1234-1234-1234-1234-56"
-# or you can use strings. Passphrase IS NOT supported
-# To use a string, prefix it with s:
-# Note - this example also sets the encryption method to open
-# which is regarded as more secure than restricted
-#key_SSID="s:foobar enc open"
-#key_SSID="s:foobar enc restricted"
-
-# If you have whitespace in your key, here's how to set it and use other
-# commands like using open encryption.
-#key_SSID="s:'foo bar' enc open"
-
-# WEP key for the AP with MAC address 001122334455
-#mac_key_001122334455="s:foobar"
-
-# Here are some more examples of keys as some users find others work
-# and some don't where they should all do the same thing
-#key_SSID="open s:foobar"
-#key_SSID="open 1234-5678-9012"
-#key_SSID="s:foobar enc open"
-#key_SSID="1234-5678-9012 enc open"
-
-# You may want to set muliple keys - here's an example
-# It sets 4 keys on the card and instructs to use key 2 by default
-#key_SSID="[1] s:passkey1 key [2] s:passkey2 key [3] s:passkey3 key [4] s:passkey4 key [2]"
-
-# You can also override the interface settings found in /etc/conf.d/net
-# per SSID - which is very handy if you use different networks a lot
-#config_SSID="dhcp"
-#dhcpcd_SSID="-t 5"
-#routes_SSID=
-#fallback_SSID=
-
-# Setting name/domain server causes /etc/resolv.conf to be overwritten
-# Note that if DHCP is used, and you want this to take precedence then
-# please put -R in your dhcpcd options
-#dns_servers_SSID="192.168.0.1 192.168.0.2"
-#dns_domain_SSID="some.domain"
-#dns_search_path_SSID="search.this.domain search.that.domain"
-# Please check the man page for resolv.conf for more information
-# as domain and search (searchdomains) are mutually exclusive and
-# searchdomains takes precedence
-
-# You can also set any of the /etc/conf.d/net variables per MAC address
-# incase you use Access Points with the same SSID but need different
-# networking configs. Below is an example - of course you use the same
-# method with other variables
-#config_001122334455="dhcp"
-#dhcpcd_001122334455="-t 10"
-#dns_servers_001122334455="192.168.0.1 192.168.0.2"
-
-# Map a MAC address to an SSID
-# This is used when the Access Point is not broadcasting it's SSID
-# WARNING: This will override the SSID being broadcast due to some
-# Access Points sending an SSID even when they have been configured
-# not to!
-# Change 001122334455 to the MAC address and SSID to the SSID
-# it should map to
-#mac_essid_001122334455="SSID"
-
-# This lists the preferred SSIDs to connect to in order
-# SSID's can contain any characters here as they must match the broadcast
-# SSID exactly.
-# Surround each SSID with the " character and seperate them with a space
-# If the first SSID isn't found then it moves onto the next
-# If this isn't defined then it connects to the first one found
-#preferred_aps="'SSID 1' 'SSID 2'"
-
-# You can also define a preferred_aps list per interface
-#preferred_aps_eth0="'SSID 3' 'SSID 4'"
-
-# You can also say whether we only connect to preferred APs or not
-# Values are "any", "preferredonly", "forcepreferred", "forcepreferredonly" and "forceany"
-# "any" means it will connect to visible APs in the preferred list and then any
-# other available AP
-# "preferredonly" means it will only connect to visible APs in the preferred list
-# "forcepreferred" means it will forceably connect to APs in order if it does not find
-# them in a scan
-# "forcepreferredonly" means it forceably connects to the APs in order and does not bother
-# to scan
-# "forceany" does the same as forcepreferred + connects to any other available AP
-# Default is "any"
-#associate_order="any"
-#associate_order_eth0="any"
-
-# You can define blacklisted Access Points in the same way
-#blacklist_aps="'SSID 1' 'SSID 2'"
-#blacklist_aps_eth0="'SSID 3' 'SSID 4'"
-
-# If you have more than one wireless card, you can say if you want
-# to allow each card to associate with the same Access Point or not
-# Values are "yes" and "no"
-# Default is "yes"
-#unique_ap="yes"
-#unique_ap_eth0="yes"
-
-# IMPORTANT: preferred_only, blacklisted_aps and unique_ap only work when
-# essid_eth0 is not set and your card is capable of scanning
-
-# NOTE: preferred_aps  list ignores blacklisted_aps - so if you have
-# the same SSID in both, well, you're a bit silly :p
-
-
-##############################################################################
-# ADVANCED CONFIGURATION
-# 
-# Two functions can be defined which will be called surrounding the
-# associate function.  The functions are called with the interface
-# name first so that one function can control multiple adapters.
-#
-# The return values for the preassociate function should be 0
-# (success) to indicate that configuration or deconfiguration of the
-# interface can continue.  If preassociate returns a non-zero value, then
-# interface configuration will be aborted.
-#
-# The return value for the postassociate function is ignored
-# since there's nothing to do if it indicates failure.
-
-#preassociate() {
-#	# The below adds two configuration variables leap_user_SSID
-#	# and leap_pass_SSID. When they are both confiugred for the SSID
-#	# being connected to then we run the CISCO LEAP script
-#
-#	local user pass
-#	eval user=\"\$\{leap_user_${SSIDVAR}\}\"
-#	eval pass=\"\$\{leap_pass_${SSIDVAR}\}\"
-#
-#	if [ -n "${user}" -a -n "${pass}" ]; then
-#		if [ ! -x /opt/cisco/bin/leapscript ]; then
-#			eend "For LEAP support, please emerge net-misc/cisco-aironet-client-utils"
-#			return 1
-#		fi
-#		einfo "Waiting for LEAP Authentication on \"${SSID//\\\\//}\""
-#		if /opt/cisco/bin/leapscript ${user} ${pass} | grep -q 'Login incorrect'; then
-#			ewarn "Login Failed for ${user}"
-#			return 1
-#		fi
-#	fi
-#
-#	return 0
-#}
-
-#postassociate() {
-#	# This function is mostly here for completeness... I haven't
-#	# thought of anything nifty to do with it yet ;-)
-#	# Return 0 always
-#	return 0
-#}